Quote:
Originally Posted by
blackbird94
Had the CW45 at the range today, along with a bunch of other stuff. Pulled the CW out to try the new Fiocchi XTP defense ammo I just bought. Magazine, rack it, doesn't go to battery. drop the mag, rack it. That round ejects, next one jams, solid. not into battery, slide will not move. Can't rack it, can't tap it into battery. I'm stuck with an inoperable pistol with a hot round almost into the chamber. Ended the range day. put it in a padded case. Locked it into the trunk. A quick 10 minute run to the gun shop/gunsmith. 5 minutes and $25 later, all is good again. Turns out, the cone on this round is too steep to go up the ramp. Shop said it's fairly common with this short a barrel pistol. It's a Horrandy XTP bullet in a Fiocchi case. Yes factory new rounds. Off tomorrow to see if the shop where I bought them will let me swap for core bon or golden saber. Oh yeah, actually dented the tip of the hollow point.
"Turns out, the cone on this round is too steep to go up the ramp. Shop said it's fairly common with this short a barrel pistol."
I doubt that's the case
. From what you wrote earlier
, "next one jams, solid. not into battery, slide will not move. Can't rack it, can't tap it into battery. I'm stuck with an inoperable pistol with a hot round almost into the chamber.", I'd guess that the XTP has engaged the barrel's rifling preventing the round from going into battery and also making it difficult to extract.
This can happen because of the round's overall length or because of the bullet's shape. We see this some in Kahr CW45s. IMO this is because they have a short amount of free bore/leade cut into the barrel. Here's a drawing to illustrate:
http://i42.tinypic.com/10fnptx.jpg
The top barrel has a short amount of free bore/leade in front of the chamber. I think it's pretty easy to see how some rounds might have a length or bullet that could contact the barrel's rifling when chambered.
As a quick test, remove the barrel and lightly drop a round into the chamber. The round should seat with the back of the case flush with or very slightly below the rear of the barrel hood: (image originally posted by John boy on SASS.net)
http://i58.tinypic.com/15d53ic.png
My guess is that your ammo will be slightly protruding (as in the far right above; the photo illustrates correct head spacing, but applies here).
If this is the case, I think you have about three options:
1. switch to an ammo that seats flush when you drop it into the chamber and operates correctly in your pistol.
2. Return it to Kahr for repair.
3. Have a local gunsmith ream the barrel to increase the "free bore".
I guess there's also a chance that your chamber is tight. If you can wiggle the round a little when it's in the chamber then I doubt this is an issue.
Abraxxas posted some excellent photos when he had a similar problem. In his case the free bore/leade was not cut evenly; you can see where he has adequate free bore/leade in the second photo and insufficient in the third:
Quote:
Originally Posted by
Abraxxas
I've read numerous posts online about Kahr's being picky about what ammo they will chamber and wont due to their tight chambers. I want to share what I found with mine tonight after I locked it up tight today on it's first trip to the range while attempting to chamber one of my target loads after 100rds of Remington factory ball ammo.
I pulled the barrel out for cleaning tonight and attempted to chamber some various ammo by dropping them in while holding the barrel. I found some dropped right in while others stopped short of fully chambering. This is easier than trying to pry my action open like I had to do at the range today I found that hollow points with a pronounced shoulder on them like Hornady XTP's and the Nosler Custom Competition 185's that I love to load so much for my other 45's were what caused the problem.
I took one that wouldnt chamber and dropped it in until it stopped and then grabbed the base of the shell with my fingers and twisted it back and forth about 90 deg while light pressing forward and pulled it out. The barrel is steel, the bullet jacket and shell case are soft metals so I knew the barrel/chamber should leave marks on the cartridge where it is hanging up. It was on the shoulder of the bullet as pictured below. On the left is a Nosler 185 handload and on the right is a Federal HydraShok. The Hydrashok drops right in, the Nosler does not... notice the difference in profiles close to the case mouth. The Hydrashok has a profile very similar to ball ammo until the top, so it chambers.
http://i46.photobucket.com/albums/f1...s/DSC_5811.jpg
Because the marks from me twisting the cartridge in the chamber are on the bullet and not the casing, I started to look at the barrel and not the chamber. The chamber is no tighter than than my other 45's just by feeling the amount of freeplay with a cartdridge fully chambered. Pictured below is the lead-in to the rifling in my barrel.
http://i46.photobucket.com/albums/f1...s/DSC_5804.jpg
It is a steeper angle than my other 45's, but not that much different... why is it touching the bullet before the cartridge is fully chambered I wondered? As Im staring at it scratching my head I noticed that the lead-in is not uniform. Pictured above is the left side of my barrel, pictured below is the right side of my barrel. Notice the difference in the angle of the bevel on the beginning of the rifling.
http://i46.photobucket.com/albums/f1...s/DSC_5803.jpg
THIS is why it will not chamber the bullets with a more pronounced shoulder profile. Is this considered defective? Normal? I dont know, this is my first Kahr. Perhaps some of you could take a look and see if your picky eater looks like this? I could get around this by changing the bullet seating depth of my target loads to work with this gun so Im not terribly concerned about it myself at this point. I did however want to share my findings because I've read a fair amount about folks having picky eaters that wont chamber certain types of ammo. Many of the threads on various forums/reviews seem to have the XTP style bullet causing the problems.
Brian
FWIW, my CW45 had this issue with Hornady 230gr. XTP. It happened with less frequency and became easier to clear as I put more rounds through the pistol, but I eventually bought a reamer and cut more free bore/leade into the barrel. Issue fixed.
http://i58.tinypic.com/rc7tc7.jpg
http://i63.tinypic.com/2ug2fbo.jpg
http://i58.tinypic.com/1zl9kdy.jpg
Regards,
Greg
