Search:

The finish is very similar in appearance to hot salt bluing done on a satin finish surface (rust blue is carded with a steel brush or fine steel wool at the end of each cycle). It can be very dark...

I use Caswell black oxide concentrate. It's a cold blue that uses chemicals similar to Birchwood Casey's Super Blue and other cold blues (Material Safety Data Sheets are readily available for...

Welcome to the forums:)
As FreeMe mentions, see if your "lead loads plunked into the chamber of my removed barrel". If they are correctly sized and don't drop fully in, I suspect the bullets profile...

Lakeline followers are good to go, They work flawlessly for me, but now, for my primary magazines, I use these: https://magguts.com/product-category/kahr/kahr-kahr/

Thanks! I enjoy viewing your work. Very nice job on the grips you posted recently.


Doing good boss, thank you for asking. Hope all is going well for you and yours.

Regards,
Greg

Thanks for the info on the 97 changes.:)
I like the thin bogie grips. I also have them on my 75B:
https://i.postimg.cc/c4tVpKPx/75-1-copy1000ac.jpg
Regards,
Greg

CZ 75 factory bushings can be kind of a pain to replace. You have to remove the front sight pin, then drive the bushing out.
Here's someone's video on replacing one:
...

Still one of my favorites and close by as I type this:typing:
https://i.postimg.cc/c1YTPcR2/stagtrp2-copy.jpg
Regards,
Greg

Congrats on the 97B:)
I have some thin grips from Lok Grips on my Witness 45 They needed a bit of work to perfect the fit, but I am pleased with them now:...

I second the 1911 grip screws suggestion:hippie:
I have some rather plain ones on my MK9, but think they enhance it's look: https://i.postimg.cc/VvXyyLdZ/mk1.jpg
Regards,
Greg

Welcome to the forums:)

As to the slide stop: my first thought would be to check the condition of the slide stop spring and verify that the spring leg is over the slide stop when installing the...

P45 or CW45 with Officers/compact 1911 magazines (near flush fit). I like the grip's angle and it's length on these pistols.
https://i.postimg.cc/Gmr3CRR8/xxp45-a1000-copy.jpg

Increasing the...

dao, That's a gorgeous OACP you have there, nice work boss!

In regards to the Clark plug, during 2008 (https://www.1911forum.com/threads/om-recoil-system-to-ismi-or-not-to-ismi.218288/ ) I put...

My P45 has one...it's been about 4 years since I installed it. Here's my the thread about it:...

That's how .22 barrel liners are done now.
Regards,
Greg

LOL, I'm in the "Philips head" camp:der:
https://i.postimg.cc/pybwZ9jV/380ph.jpg

They make an adapter for .920 dia. barrels: https://www.tech-sights.com/product/920-barrel-dovetail-adaptor/
I've seen photos of them on some Project Appleseed builds:...

If you were correct in your first post about your current spring, I'd put the open end in the hole on the striker block. That way the open end is guided by the hole's wall. If you gun has functioned...

Well shoot:confused:, maybe try a direct link: https://i.imgur.com/7Fz4kbw.jpeg or https://i.postimg.cc/wxQD8Htq/gripsj45.jpg

Maybe this will work for you Colonel
https://i.imgur.com/7Fz4kbw.jpeg

Those grips look really good on your pistol:)
Regards,
Greg

It looks to me that the handle bar stem is a foldable type. You can probably find a shorter folding stem online. At the very least, a shorter conventional bike stem could be fitted.

Do you think...

https://i.postimg.cc/mgFtLP5N/watts.jpg

Nice ride Colonel!

I'm probably preaching to the choir here, but I'd rather say it than later regret not having said it.Your trike looks to have a fairly high center of gravity and being that...

Welcome aboard!:w00t: