Tommy Gun Shop   Mitch Rosen   Kahr Shop   Crimsontrace

Search:

Type: Posts; User: Noway

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    23
    Views
    3,202

    TFOs were a no-go as the front sight did work out...

    TFOs were a no-go as the front sight did work out of position when I shot it. Groan. I have replaced beaucoup sights in my day, but never as problematic as with this gun... :(
  2. Switched out the mag release and voila no more...

    Switched out the mag release and voila no more dropsy!

    It's a cute little gun but will probably never take the place of my Sig P938 as a bug...
  3. Thanks for the link. My CT380 and PM9 are two of...

    Thanks for the link. My CT380 and PM9 are two of the most finicky guns I have ever owned! :p
  4. Happens weak-handed and one-handed as well. Just...

    Happens weak-handed and one-handed as well. Just installed a new magazine release. The old one looked like someone had filed it down, and a new gun no less.
  5. Happens with all three mags. Removed the...

    Happens with all three mags. Removed the internals and had a look where the catch engages the cut-out. Not seeing anything preventing the catch from engaging, but it barely does so. I'm getting a new...
  6. Replies
    23
    Views
    3,202

    Installed the TFO sights, but the front sight...

    Installed the TFO sights, but the front sight base does not sit flush on the slide in the dovetail. For some reason it has positioned itself about 1/2 mm up so there's daylight visible between the...
  7. Good suggestions, thanks!

    Good suggestions, thanks!
  8. CT380 mag dropping on 6th-7th rounds - loose spring mayhaps?

    Shooting strong-hand two-handed I find that the magazine often drops free before the 6th or (especially) the 7th round chambers.

    The mag release seems to be a bit loose all things considered.
    ...
  9. Replies
    23
    Views
    3,202

    Yes, I guess it's common-sense, but at that point...

    Yes, I guess it's common-sense, but at that point I was being very wary.


    Success, although the dovetail is a wee bit on the loose side. Will take it to the range and see if it holds zero, if not...
  10. Replies
    23
    Views
    3,202

    Got the dovetail base out after making the cut. ...

    Got the dovetail base out after making the cut.

    Now, install from the left or the right (strong hand side or weak hand)?

    There are a few YT videos on installation, but nothing particular to...
  11. Replies
    23
    Views
    3,202

    Thanks, that was my inclination (guess), but I...

    Thanks, that was my inclination (guess), but I had to stop for the night as I was getting irritated and the garage is about 95 degrees... This will require some cautious deliberation.

    When you get...
  12. Replies
    23
    Views
    3,202

    So, installing TruGlo TFO sights. Rear sight...

    So, installing TruGlo TFO sights. Rear sight comes out okay, although there appears to be a tiny bit of rust in the dovetail cut. Seated the new sight with no problems at all.

    Front sight, working...
  13. Replies
    23
    Views
    3,202

    Using the Dawson Precision sight calculator I...

    Using the Dawson Precision sight calculator I need a front sight .230” high; stock is .180”. Or figure out a different hold.

    or maybe buy aftermarket sights and just be done with it.
  14. Replies
    23
    Views
    3,202

    Thanks. I'll check that next time at the range,...

    Thanks. I'll check that next time at the range, but on two sessions shooting a variety of ammunition the offset has been virtually identical. I've never had this issue before with any handgun I can...
  15. Replies
    23
    Views
    3,202

    Factory sights, on the rear at least. I assume...

    Factory sights, on the rear at least. I assume the front sights are factory too.
  16. Replies
    23
    Views
    3,202

    This is useful:...

    This is useful: https://dawsonprecision.com/sight-calculator/
  17. Replies
    8
    Views
    1,699

    Back out for a follow up. Golden Saber HP is GTG,...

    Back out for a follow up. Golden Saber HP is GTG, Geco still a non-starter, and my reloads were not bad at all. A few of the latter didn't quite chamber, but I'll reduce the OAL and see if that...
  18. Replies
    23
    Views
    3,202

    Yes. Was out to the range again today, shooting...

    Yes. Was out to the range again today, shooting 115, 135 +P and 147 and no real difference among them (aside from +P recoil). Wondering if the former owner didn't change out the front sight at one...
  19. Replies
    23
    Views
    3,202

    Thanks, it's worth a try. Also need to run some...

    Thanks, it's worth a try. Also need to run some JHP through it.

    Curious how the height of the factory sights compares with the DP sights, even some increment may make a big difference.
  20. Replies
    23
    Views
    3,202

    Shooting high with my new-to-me PM9

    At least with Blazer 115 gr I ‘m consistently hitting 3-4 inches high when I center my front sight on the bullseye. When I use a VERY low 6 o’clock hold I hit the center.

    Good groupings, just too...
  21. Replies
    40
    Views
    3,752

    Here's one I dug up: ...

    Here's one I dug up:

    https://www.lymanproducts.com/brands/pachmayr/grip-extenders/mag-sleeves
  22. Replies
    40
    Views
    3,752

    Where is this mythical beast sold? Couldn't...

    Where is this mythical beast sold? Couldn't Google it...
  23. Replies
    5
    Views
    1,134

    Okay, just got the rebate and applied it toward...

    Okay, just got the rebate and applied it toward Trijicon sights for the 380. That was easy!
  24. Replies
    8
    Views
    1,699

    Also storing it with the slide locked open, for...

    Also storing it with the slide locked open, for what that's worth.

    The next range trip will probably be limited to +P ammunition...

    Also going to try some reloads. THAT should be...
  25. Replies
    8
    Views
    1,699

    My CT was also filthy after this modest outing,...

    My CT was also filthy after this modest outing, on a scale I haven't seen since I fired Norinco ammo in my Makarov years and years ago. So it's possible some of that soot was gumming things up a bit...
Results 1 to 25 of 28
Page 1 of 2 1 2
Tommy Gun   Xssights   Magnum Research new   CrossBreed Holsters