Kahr Shop   Crimsontrace   CrossBreed Holsters   Tommy Gun Shop

Search:

Type: Posts; User: kahrinca

Page 1 of 6 1 2 3 4

Search: Search took 0.06 seconds.

  1. Good to hear, Barth! Sent from my...

    Good to hear, Barth!

    Sent from my SAMSUNG-SGH-I337 using Tapatalk
  2. O'Dell- Look who's calling the kettle black. ...

    O'Dell-

    Look who's calling the kettle black.

    Not only do you mischaracterize my posts in this thread, you personally attack me in violation of numerous forum rules. Smear.

    I am quite happy...
  3. Check out 7:22 to the end, doesn't fare well with...

    Check out 7:22 to the end, doesn't fare well with the extended mag:

    https://www.youtube.com/watch?v=aCZu2LXTqbQ

    On another point- purchased a CW9 seven or eight years ago. You are correct-...
  4. I am not willing to accept and dismiss a probable...

    I am not willing to accept and dismiss a probable defect in the Kahr extended magazines just because the platform's not a Glock.

    Rather than buy the ugly Block, I'd rather see Kahr extended...
  5. My new PM9 to my surprise came with three...

    My new PM9 to my surprise came with three magazines- two 6-rd (yes!) and one 7-rd extended. It's not like one has a choice.

    One might speculate that Kahr purposely provides two 6-rd mags due to...
  6. Every time I've shot the extended 7-rd magazine...

    Every time I've shot the extended 7-rd magazine I've had one in the chamber for a total of 8. Very early in the break-in I had 1 failure to feed that was easily remedied.

    I do think the magazine...
  7. Well, I started this thread due to frustration...

    Well, I started this thread due to frustration with myself for messing up the appearance of a NEW PM9. Perhaps I may not have felt this way if gun were purchased used in the same condition. But it...
  8. I would think so without difficulty. Just...

    I would think so without difficulty. Just waiting on some new grip tape that I ordered.

    The ones depicted are Decal Rubber Grip tape-they give quite a bit more traction than Talon rubber- a bit...
  9. Don't confuse my method with Greg's...

    Don't confuse my method with Greg's sanding/tapping.

    I used heat gun remedy, nothing else, though I initially started with a hair dryer.

    Recommend heat gun on 'low' setting. On high...
  10. Sticky: KAHR FAQ for those who don't want to do modifications and wish to carry Condition 3

    FWIW- Found this in the FAQ section on the Kahr website.

    "

    Q. My firearm fails to chamber the first round when I pull back the slide and release it. What is wrong?

    A. It is likely you are...
  11. Just an example. I don't care for Glocks much...

    Just an example. I don't care for Glocks much and don't own any.
  12. Replies
    22
    Views
    5,097

    ^^^^^ Indeed, that was an amusing post! Sent...

    ^^^^^ Indeed, that was an amusing post!

    Sent from my SAMSUNG-SGH-I337 using Tapatalk
  13. Replies
    32
    Views
    10,930

    Doesn't make all that much sense to me. Seems...

    Doesn't make all that much sense to me. Seems like using a bandaid over a cut that won't heal.

    I think there may be other issues unrelated to cleanliness of the firearm involved, but I am...
  14. Thanks for your comment, wyntrout. It's good...

    Thanks for your comment, wyntrout.

    It's good that such a 'striker block' test is available. It should especially be performed after reassembly of a stripped slide and before attaching it to the...
  15. I didn't last night. I stayed up all night...

    I didn't last night. I stayed up all night 'fretting' over it! NOT!

    It wasn't until today after reading some of the helpful posts above that it worked! Placed the unsharpened flat end of the...
  16. Replies
    22
    Views
    5,097

    Wow, be careful, Colonel. Those nipples are...

    Wow, be careful, Colonel. Those nipples are supposed to protrude other side and facilitate lock-up and that gun does not fall apart.

    But what do I know? I'm a relative newbie compared to y'all!
  17. Assuming that your theory is a correct one, it's...

    Assuming that your theory is a correct one, it's totally unacceptable. A Glock 26 can fire just fine with a 17 or 33-rd mag attached.
  18. Traditional firing pin pencil test? Myth, or valid test with a Kahr PM9?

    My new PM9 has fired every time- no light strikes. Have inspected empty casings and the strikes have the irregular pattern, which is normal according to the manual.

    Out of curiosity, yesterday...
  19. Is that similar to the expression: "If it's...

    Is that similar to the expression: "If it's broke, don't fix it? :(

    Part of any solution is acknowledging there's a problem. If it's merely a matter of break-in, that's one thing.

    If not...
  20. Replies
    22
    Views
    5,097

    A long time ago someone who had excellent writing...

    A long time ago someone who had excellent writing skills said to me: "Ask yourself 'what is it that I want to say?' Then, when you know what it is that you want to say, you are more likely to write...
  21. Why do the Kahr extended magazines exhibit problems?

    There have been many anecdotal reports of for instance, the 6-rd PM9 magazines as relatively trouble-free, but if one has a feeding or other problem, it seems to occur almost without exception with...
  22. Replies
    22
    Views
    5,097

    Who would STEAL a Kahr slide stop? That stopped...

    Who would STEAL a Kahr slide stop? That stopped the thread for me right there.

    Oh, must've been a stolen PM9 gun....sorry...ggggeeeessshhhh...
  23. Replies
    69
    Views
    28,638

    Oh, please! You are far better off with the 938...

    Oh, please! You are far better off with the 938 and 9mm ammo unless you can't hit the side of a barn with it. 9mm does significantly better in ballistic testing than .380.

    Also, I am NOT...
  24. Replies
    69
    Views
    28,638

    The P380 is extremely small and impressive, and...

    The P380 is extremely small and impressive, and it's also quite expensive here in CA. After reading this thread and elsewhere, don't think I'd buy the P380. One shouldn't have to go to such lengths...
  25. Replies
    15
    Views
    5,398

    Your comments are encouraging. I thought the...

    Your comments are encouraging.

    I thought the 'Proper prep of a new Kahr' suggestion to spray the 'striker channel hole' in the slide was such a good tip that I had to try it years ago with my...
Results 1 to 25 of 131
Page 1 of 6 1 2 3 4
Mitch Rosen   Tommy Gun   Magnum Research new   Xssights