+1 for all the other comments. It will be a little bit of a challenge at 1st but you will figure it out. Mine has a 1000 rounds through it and still takes a little bit of determination to get it back...
Type: Posts; User: z8894
+1 for all the other comments. It will be a little bit of a challenge at 1st but you will figure it out. Mine has a 1000 rounds through it and still takes a little bit of determination to get it back...
@pzlehr. I can relate to that. I have Glocks, like them and will keep them. I prefer the Kahr trigger, ergonomics and concealability. I love my Glock 26 but if I had found the CW9 1st would have...
Mine is working fine. I'm very sure it will way out last the recoil springs. If there is any news on recoil springs, I'll be interested to hear it.
I've got a Glock and a CW9. Nothing wrong at all with the Glock trigger but I prefer the Kahr. I've seen youtube videos of people slowly pulling and over exaggerating the Kahr trigger pull. Pull it...
Just to wrap this thread up. Kahr sent the standard sight just as they said they would. There were no instructions, just the sight. I stuck it on and touched both posts lightly with a Weller 40w...
Thanks RonW. My CW9 came new with the Trijicon night sight installed by Kahr. It looked fine, I never noticed a problem till it wasn't there any more. Kahr is sending me the standard front sight so...
Thanks gb6491. I wish had paid more attention to the sight before it came off. The sight sat flush to the top of the slide. The screw on the back post was slightly counter sunk. No flair on the...
He either said that or "Stay away from plastic sights" . I don't hear as well as I used to, just ask my wife.
Thanks CJB. On the CW9 the front sight is plastic and pinned in. The back post broke when it went flying off so it will have to replaced. Epoxy might hold but I don't think I would trust it.
Went to the range today and after about 30 rounds I had trouble picking up the front sight on a follow up shot. After a closer look, I had no front sight! I found it on the floor about 12 feet...
I got to shoot it this morning. 100 rounds with no issues at all. It shot great, it was me that shot a little low and left. Pretty good for the 1st time shooting it though. I still love my CZ, Sig,...
I'm no expert but it looks like the answer is, no. http://www.kahr.com/kahr-mag-guide.asp#9mmmag
I bought it. Here it is cleaned, lubed and ready to go. It will be next weekend before I can shoot it.
http://i76.photobucket.com/albums/j38/keith_sweat1/0424160906a1_zpseezyhr0u.jpg
My wife has a G42 and it occasionally doesn't lock open. We've determined the cause to be limp risk. Works fine when I shoot it. It had a few cycling issues in the 1st 100 rounds. No problems...
It was still there today. I felt it up again but I'm about $100 short. Creative financing may resolve the problem.
The only Kahr I've ever shot is my CW380. I bought it for its size, the ability to conceal it and carry it most anywhere. My hands are way too big for it though. I can shoot it pretty well but it is...
I have a CW380 and a Sig P320 (Sig P250 too). I agree with berettabone, you just need more trigger time. I love the Kahr trigger but it is a little different. Get some snap caps, spend some time,...
It's a Clinger Stingray. Works well for appendix carry.
https://clingerholsters.com/product/stingray-strong-side-clinger-holster/
New Striker installed and a trip to the range. Works great. I had the original striker break at 540 rounds. It's replacement had +1200 rounds on it with no problems. This one should last forever.:)
...
I'll be ordering one too. I had one break and your design addresses exactly what I think the problem was.
+1. Got an e-mail today that it's on the way.
I've got a CW380 that I've put 1100 rounds through. It had a couple of hiccups in 1st 100 rounds (not unexpected for any gun) but it has run very well since. The striker did break at 540, I had done...
I have a Kahr and a Glock (plus others). I like both. I think he isn't used to the dual action trigger concept. With your finger on the trigger of a Glock and having taken up the slack, it's about...
I was using Freedom Munitions 100 grain RNFP when the stiker broke. They fed fine but but the recoil was much more than the varieties of 95 grain I had been using. They were a good deal and I bought...
RH7XXX serial number for mine.