Search:

Welcome. It will be easy to convince your wife of the need for a handgun. Let her watch the evening news for a week or so.

^^^ +1

I found the screw securing the slide lock spring to be loose, when experiencing the same problem. The spring was loose enough to not hold the slide lock in the down position. Recoil from...

I purchased a CW380 a couple of months ago. I joined the forum to find out everything possible about my new pistol. There were a couple of issues during and near the end of the break in period. I...

They have been doing this for decades. It is a great service to those in need. Clean drinking water is often difficult to obtain after a natural disaster.

I have put close to 200 rounds through the CW380 since it returned from Kahr. The pistol now runs flawlessly and is a pleasure to shoot. It shoots so well, I thought it could use some new pants. I...

I am glad to hear, you had good results with the pistol.

That is about the same repairs they made to my CW 380. It has been flawless feeding 4 different kinds of ammo since it's return. I did have to tighten the slide lock spring screw a little. I took...

Fixed and running as smooth as glass. I removed the slide and inspected the slide lock lever spring. The screw and washer were loose. This allowed the spring to move and not put tension on the...

Update:

I put 42 rounds through it. There were no failure to feed or light strike issues. I now have a new problem. The slide is locking back after the fifth round of both six round magazines. ...

I got the pistol back from Kahr yesterday. The service work sheet says the extractor port and slide were reworked and cleaned. They installed a new extractor and extractor rear pin. The pistol was...

It will be back from Kahr tomorrow. I am looking forward to having my pistol back. I will let you guys know what was done to it and how it performs.

Pick up a used Remington 870 from a local pawn shop. It costs @ 10 bucks to change the internals over to the 870 Police workings. If it is chambered in 2 3/4" or 3" you are good to go either way. ...

The CW 380 has been with Kahr since Friday. When it comes back, I plan to polish the feed ramp and chamber. If Kahr does not dis-assemble and clean the slide, that will be done also.

I would be confident and competent in the dis-assembly of the slide. I would just rather send it back and let them diagnose and fix anything that may be the culprit. I have read enough on this...

Page 17 of the operating instructions addresses the dis-assembly of the slide. " DO NOT DISMANTLE THE PISTOL FURTHER THAN THE MAIN COMPONENTS DESCRIBED ABOVE (except magazine). To do so may create...

I talked with the guy that makes these. He recently started using 9oz. leather. He says it is @ 1/32" thicker than what he had previously used. This should help to keep it a little stiffer in the...

The inner recoil spring is shorter than the outer. Should you place the closed end of both springs at the barrel end of the guide rod. Should both open ends be flush at the point where the guide...

I tried this. I put 2 drops of Hoppe's oil on the rails on the slide. I allowed these to run down the entire slide. I oiled the metal slide rails on the frame. I put a little oil on the feed ramp...

I have put well over the 200 rounds as break in. I have spent over $200 on ammo trying to get it to feed and fire. I had to work hard for the money to pay for the ammo and the pistol. A new...

Between session the gun was disassembled and thoroughly cleaned and lubed. The striker channel was cleaned. The barrel, feed ramp, and breach face were all cleaned very well. The recoil guide rod...

Today's session was pathetic. I used four different kinds of ammo: Golden Sabre, Winchester train & Defend, Critical Defense, and Hornady American Gunner with XTP. There was no distinction between...

I took the new CW 380 out for a few rounds. I had lubed the pistol. I did not clean the striker channel before this outing....

I ordered one of these today. The chestnut brown should look good with my CW 380. His current price is $26 shipped. That is the lowest price I have found for a good back pocket holster. I...

I have been reading here for days. The amount of information available is tremendous. I look forward to becoming a part of your community.

I thought this would be the best starting point. I have been hunting and shooting for @ 35 years. If it has anything to do with guns or knives, I am ready. I purchased my first Kahr pistol last...