A lot of work in that. Beautiful.
A lot of work in that. Beautiful.
In Memory of Paul "Dietrich" Stines.
Dad: Say something nice to your cousin Shirley
Dietrich: For a fat girl you sure don't sweat much.
Cue sound of Head slap.
RIP Muggsy & TMan
"If you are a warrior legally authorized to carry a weapon and you step outside without that weapon, then you become a sheep, pretending that JOCKO will not come today."
Ok, so pretty much done. A few issues... Neither the factory grip screws fit (protrude into the magwell preventing mag insertion) nor do the aftermarket screws (screws to short to reach the frame on the bottom). Too brain fried after getting the trigger back in to even think about that stuff for a while. Second issue is the REALLY poor fitting rear sight (pic attached). Not sure what they were thinking there. Forget if I got those from Kahr or flea bay, but again, thats for another day when my brain isn's smoking (about to crack a coldy over this). Function check is fine. New stainless guide rod in there too. New grips came in for a Kimber, so snuck a shot of it in there too! Lastly, a shot of the trigger bar contact point of the frame. It was difficult getting in there. I polished both sides, so it will also ride smoother against the grips. I have not shot, or pulled the trigger in a while, so I can't tell you if there's any seat of the pants difference in feel, but she feels smooth as buttah!
That rear sight isn't even close to being the right one for that gun.
Every thing else looks marvelous. I've heard installing the trigger and trigger bar are a bit of challenge. Never went there myself. Hopefully will never have to.
Did you try the grip screws out of the Kimber for length, might just work. Not sure what Al uses for screws on his grips.
In Memory of Paul "Dietrich" Stines.
Dad: Say something nice to your cousin Shirley
Dietrich: For a fat girl you sure don't sweat much.
Cue sound of Head slap.
RIP Muggsy & TMan
"If you are a warrior legally authorized to carry a weapon and you step outside without that weapon, then you become a sheep, pretending that JOCKO will not come today."
On a side note, once I complete the little AMT, it's on to the MK9. I already have the LL grips, but waiting on the mag sleeve and floor plate. I want to put a stainless guide rod in it, and new sites as well. I just have to take a break from polishing and spending, or I may be a single guy soon! Lol!
Those grips with that polished pistol just makes the whole project sing. Very nice work.
The only thing better than having all the guns and ammo you'd ever need would be being able to shoot it all off the back porch.
Want to see what will be the end of our country as we know it???
Visit here:
http://www.usdebtclock.org/
Wow. You do nice work. Thanks for sharing it.
Aftermarket accessories for Kahr Pistols at https://lakelinellc.com/
There are always more in the pipeline...
^^^ Beautiful work. FYI - I've filed down grip screws before. It's easy. Just file a little, test and repeat. It's even easier if you have a grinding wheel. Hope that helps.
O|||||||O
Thanks guys!
b4uqzme, I have considered that. Problem is, the one's that are too long are the flat head, not hex/allen in stainless that I'm wanting on there. I think once I find longer ones, your approach is most likely what I will have to do. Man, can anything be easy with these things?
I missed the grip screws thing earlier. The factory grip screws should work fine. They do on both of my K9s with those grips. One pretty easy way to take up some space that has another advantage is taking a small o-ring and putting it under the screws. You have to find a pretty thin one. The additional advantage is it keeps the screws from backing out while shooting too.
Aftermarket accessories for Kahr Pistols at https://lakelinellc.com/
There are always more in the pipeline...