Magnum Research new   Kahr Shop   Crimsontrace   CrossBreed Holsters
Results 1 to 6 of 6

Thread: CW380 not feeding top round in magazine

  1. #1
    Join Date
    Jul 2016
    Posts
    24

    Default CW380 not feeding top round in magazine

    I've had my CW380 for well over a year now, and have shot maybe 2000-2500 rounds through it. I've had most of the growing pains during the Kahr break-in period, and have done a lot of the sticky note modifications like MagGuts, Lakeline striker, extractor claw and pin grinding, all after a useless return to the factory. I just about thought I had it running smoothly, until the top round of a full magazine stopped feeding consistently. The first 2-3 magazines of Hornady Critical Defense usually cycle through a clean gun flawlessly. Then during the 3rd or 4thmagazine is where the problem begins. I manually load a round in the chamber, then release the locked-back slide and load a full magazine. After the first shot fires, the first round from the magazine doesnít feed at all. Itís not the failure to return to battery problem which required a slap to the back of the slide like during the break-in period, but a complete lock up. The magazine wonít release until I pull the slide back another 1/8 inch where it locks open. Then I can release the magazine, and the top round is still seated in the magazine. Most of the time, but not always, I can reload the dropped mag, and the remaining rounds cycle as they should. When this problem began, I decided to replace the recoil springs, but that didnít help. Then I thought maybe it was an issue with the magazines, but I have 3, and they all have MagGuts replacements, and all work the same. Other practice rounds, Winchester white box flat nose, and Remington round nose preform the same eventually. They might run well through a few magazines, but eventually act up the same way as the Hornady CD. Itís like the ammo Iím using doesnít have enough kick to cycle the slide back far enough to pick up the next round off the magazine. But then why have those brands worked well up to this point? Doesn't seem to have a loose or bent ejector. Maybe +P rounds, but why now and not before? Any ideas?
    Last edited by dhenze; 09-13-2018 at 08:14 PM. Reason: poor formatting

  2. #2
    Join Date
    Sep 2009
    Location
    Wet & Wild Pacific NW
    Posts
    27,922

    Default

    To start with I never load the chamber and drop the slide on that round. I lock the slide back, insert the mag and then drop the slide either by tugging it back a bit and letting fly or just hitting the slide release.

    Doing it the way you describe makes the extractor climb over the case rim, there's enough travel in a Kahr that it may not be an issue, some other guns it's a definite bad thing and probably best to stay consistent and not do it to any.


    Far as hanging up half way back unless you lift the slide release, that's a bit perplexing. I'd try loading as I describe first. It might be the extractor is not fully engaging the round in the chamber slowing things down a bit or enough not to cycle.

    Smarter folks than I will be along shortly. We'll get to the bottom of this, count on that.
    http://bawanna45.wix.com/bawannas-grip-emporium#!
    In Memory of Paul "Dietrich" Stines.
    Dad: Say something nice to your cousin Shirley
    Dietrich: For a fat girl you sure don't sweat much.
    Cue sound of Head slap.

    RIP Muggsy & TMan

  3. #3
    Join Date
    Jul 2016
    Posts
    24

    Default

    Thanks, Bawanna

    Not manually loading the first round makes sense. I checked the Kahr user guide and saw your recommendation was stressed there as well. That would explain why I've had minimal misfires after reloading the magazine after the failure.

  4. #4
    Join Date
    Sep 2009
    Location
    Wet & Wild Pacific NW
    Posts
    27,922

    Default

    I should probably read the users manual myself, probably some good stuff in there.

    I generally glance at them but seldom read them carefully.
    http://bawanna45.wix.com/bawannas-grip-emporium#!
    In Memory of Paul "Dietrich" Stines.
    Dad: Say something nice to your cousin Shirley
    Dietrich: For a fat girl you sure don't sweat much.
    Cue sound of Head slap.

    RIP Muggsy & TMan

  5. #5
    Join Date
    Jun 2018
    Location
    Missouri
    Posts
    124

    Default

    Quote Originally Posted by dhenze View Post
    Thanks, Bawanna

    Not manually loading the first round makes sense. I checked the Kahr user guide and saw your recommendation was stressed there as well. That would explain why I've had minimal misfires after reloading the magazine after the failure.
    I experimented with my CW380 when I first got it, and manually loading the first round did not work out well.

  6. #6
    Join Date
    Jun 2018
    Location
    Missouri
    Posts
    124

    Default

    Quote Originally Posted by Bawanna View Post
    I should probably read the users manual myself, probably some good stuff in there.

    I generally glance at them but seldom read them carefully.
    I'm glad I'm not the only one.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Tommy Gun Shop   Xssights   Tommy Gun   Mitch Rosen