Tommy Gun   Crimsontrace   Xssights   Tommy Gun Shop
Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: Holster compatibility for Kahr PM9.

  1. #1

    Default Holster compatibility for Kahr PM9.

    Looking to for a quick release holster for my PM9. Want to install it near a center console in my Jeep on the Molle panel . Blade-tech, Safariland, Alien Gear make quick release holsters but not for Kahr PM9. Here's my dilemma: will PM9 fit other holsters like Glock 43, M&P Shield, Walther PPS, Sig P365 etc? Don't want to buy something and later regret it. Any thoughts?

    Molle_Panel_1.jpg

  2. #2
    Join Date
    Feb 2020
    Posts
    906

    Default

    So will this firearm be visible inside your car?

    Are you looking for a retention holster like an ALS that you can mount to this bracket?

  3. #3
    Join Date
    Mar 2012
    Posts
    1,653

    Default

    May not be the exact answer you are looking for and knowing others on this forum know far more than me about guns/holsters ect, but i have found that the sig p 365 and pm9 are pretty compatible as far as the holsters i have. " of course did but a new one anyway for my sig." also on occasion when going for long drives i will put my remora holster between the drivers seat and console of my jeep. Fits snug/nicely. Easy to draw from if needed and easy to take out and take with me when getting out of my jeep.
    "If we ever forget we are one nation under God, then we will be a nation gone under." Ronald Reagan

  4. #4
    Join Date
    Feb 2020
    Posts
    906

    Default

    Yes, we need more info in order to help.

    Are you looking for retention?

    Do you plan to leave your gun in the car all the time?

    I have found an ankle holster to be pretty fast of a draw while seated. On long drives (trips) I generally wear an ankle holster for my backup.

  5. #5
    Join Date
    Sep 2010
    Posts
    7,215

    Default

    What Grotman said about the P365 and CM9 being very close is true. I have both. In a leather holster it would be very close. Something in nylon with a thumb snap would probably work real well and not be too expensive to try. The nylon thumb break type worked real good in my truck at one time in the past for a 1911. If I remember right it was a $10 uncle Mikes holster with some Velcro.
    The only thing better than having all the guns and ammo you'd ever need would be being able to shoot it all off the back porch.

    Want to see what will be the end of our country as we know it???
    Visit here:
    http://www.usdebtclock.org/

  6. #6

    Default

    Would like to install the fast release base on the Molle panel and keep the pistol holstered there while driving, then transfer the firearm back to my belt when getting out. So, I would need 2 quick release

    bases to make this happen that way the firearm will never be unattended. Here's the link to the Blade-tech video featuring TMMS kit - https://www.youtube.com/watch?v=R-exh6NviS0 and Safariland QLS kit

    https://www.youtube.com/watch?v=k1TIeGbhn-I
    .

    The only caveat - Kahr PM9 is not on the list for these type of holsters.

  7. #7
    Join Date
    Jan 2010
    Location
    Near the Gila Mountains in SW AZ.
    Posts
    5,550

    Default

    DARA makes an OWB kydex holster that uses three screws to mount carry attachments to it. The screws are in a pattern that looks similar to the Blade Tech TMMS. Perhaps the two are compatible (I'm not sure about the spacing of the top two screws).
    https://www.daraholsters.com/owb/
    https://blade-tech.com/products/large-tmms-kit
    Regards,
    Greg
    [<a href=http://i43.tinypic.com/2n7fnux.gif target=_blank>http://i43.tinypic.com/2n7fnux.gif</a>

  8. #8

    Default

    To make it more concealable decided on different approach, ordered multi-purpose carry bag from Opovoo. https://www.opovoo.com/collections/w.../edc-waist-bag
    Should do the job, I think.

  9. #9

    Default

    Finally I was able to finish my project. Secured the multi-purpose bag to the Molle panel, inserted DeSantis Nemesis and my PM9. Fits perfectly, easy to draw and totally concealable.

    IMG_5719.jpgIMG_5720.jpgIMG_5721.jpg

  10. #10
    Join Date
    Feb 2020
    Posts
    906

    Default

    If it's working for you and you're happy, then great.

    I personally don't want a bag of any kind showing....but I'm a libertarian, glad you are happy.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
CrossBreed Holsters   Magnum Research new   Kahr Shop   Mitch Rosen