Activity Stream - KahrTalk Forums

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

04-01-2025, 08:10 AM

340pd started a thread April Foolishness in General Discussion

132 replies | 8576 view(s)

04-08-2025, 06:17 PM

kiddenme started a thread CM9 Serial Number Location in New Member Area

Hello, new here I recently purchased a Kahr CM9 and my serial number is in the lower portion of the grip and I noticed others are on the lower front...

14 replies | 1042 view(s)

04-11-2025, 01:34 PM

Slow Burn started a thread P380 failure to eject in P, S, and CW Series Pistols

At the range, after shooting off about 50 or 60 rounds with my trusty P380, an empty shell casing just stayed in the chamber. I had to pry it out...

10 replies | 1580 view(s)

04-16-2025, 03:53 PM

taroman started a thread Slide Stop Spring Tool in PM and CM Series Pistols

Reassembling my PM45 is a bit fiddly as far as getting the slide stop pad under the spring. Went to my watch repair kit revealed the perfect...

6 replies | 640 view(s)

04-20-2025, 10:05 AM

Moonshot started a thread PM9 grip mod in PM and CM Series Pistols

I have an older PM9 that I keep as a carry gun for those times when my G26 with optic is too big. One major concern I have with my PM9 is a...

6 replies | 252 view(s)

04-22-2025, 06:40 PM

04gtofan started a thread Working Diagram in PM and CM Series Pistols

Sorry folks if this is a rehash. Looking for the Kahr animated video once available on the website. Any ideas, a link would be appreciated. Thank you.

6 replies | 534 view(s)

04-04-2025, 03:30 PM

taroman started a thread New PM45 Slide not locking back in PM and CM Series Pistols

New gun, Field stripped following directions. Cleaned and did 10-point lube. Installed slide following the 4 3 slide install process. For the life...

6 replies | 501 view(s)

04-17-2025, 07:00 AM

berettabone started a thread Fyi PSA in Ammunition

4 replies | 692 view(s)

04-07-2025, 02:26 PM

harrydog started a thread For Sale WTS - Holsters for PM9 and K9 in Non-firearms for Sale

Vintage Lou Alessi OWB RH holster for Kahr K9. Easy on/off Talon clips fit up to 1.5" belt. Very good condition. $100 or make offer. $7 shipping ...

1 replies | 558 view(s)

04-15-2025, 10:15 PM

DougGuy started a thread Stock Recoil Spriing Weight CW45 in P, S, and CW Series Pistols

oo these springs get stiffer over time? I went to take mine down tonight and it had been awhile since I have needed to, but either I have gotten...

2 replies | 283 view(s)

04-15-2025, 09:08 PM

FreeMe started a thread Which rubber grip sleeve for CT45? in TP, ST, and CT Series Pistols

Hogue doesn't list one specifically for the CT45 or any 45. Pachmeyer seems to be AWOL. I see some other questionable brands on Amazon but haven't...

1 replies | 324 view(s)

04-22-2025, 04:23 AM

JohnR started a thread Please wait while your request is being verified in Technical Support

Sometimes when I log on, I get this full screen message for a second or two. Is it supposed to be there? iPhone/Safari

1 replies | 245 view(s)

04-21-2025, 09:44 AM

berettabone started a thread GB in Other Firearms Discussion

For those who are interested and haven't perused in a while............GB has T's for sale. Kahr owners must have come out of the woodwork. Noticed a...

0 replies | 291 view(s)

04-08-2025, 01:23 PM

berettabone started a thread Fyi in Ammunition

PSA Today only.............Win 9mm 115 gr. FMJ 50 rds. $10.49

0 replies | 220 view(s)

Today, 09:34 AM

tokuno replied to a thread Working Diagram in PM and CM Series Pistols

Aha, my "saveas" shows only jpg, but if I manually change the file extension to gif, then it saves and runs as the animation. Thank you!

6 replies | 534 view(s)

Today, 06:35 AM

340pd replied to a thread April Foolishness in General Discussion

132 replies | 8576 view(s)

Today, 06:31 AM

340pd replied to a thread April Foolishness in General Discussion

132 replies | 8576 view(s)

Today, 06:23 AM

340pd replied to a thread April Foolishness in General Discussion

132 replies | 8576 view(s)

Yesterday, 08:08 PM

04gtofan replied to a thread Working Diagram in PM and CM Series Pistols

Seems like the Kahr site had a much more detailed version of this. Or am I remembering incorrect?

6 replies | 534 view(s)

Yesterday, 10:02 AM

340pd replied to a thread April Foolishness in General Discussion

132 replies | 8576 view(s)

Yesterday, 07:54 AM

Whiskeyhorse replied to a thread New CM9 for under $300 in General Discussion

The best place IMO to find deals on any gun is "Slickguns". At least a good place to start. And do not forget used Kahr's, These guns are built...

9 replies | 817 view(s)

Yesterday, 05:37 AM

berettabone replied to a thread New CM9 for under $300 in General Discussion

Finally selling for what it's worth...........................sooooooo many choices these days. Lots of CM's out there. I paid $40 less than that for...

9 replies | 817 view(s)

Yesterday, 05:35 AM

berettabone replied to a thread Is K9 Elite Still Being Produced? (K9098) in K Series Pistols

I know.............reading is fundamental.....................

17 replies | 8637 view(s)

Yesterday, 05:02 AM

MarkAllen4345 replied to a thread New CM9 for under $300 in General Discussion

That’s a solid deal—$267 for a new CM9 is tough to beat, especially if you're already planning to swap the sights. The three-dot setup is totally...

9 replies | 817 view(s)

04-24-2025, 08:59 PM

getsome replied to a thread April Foolishness in General Discussion

Saw a septic service truck that had lettered on the back, “Another full load of politicians promises”………Had to give that one a Yep……

132 replies | 8576 view(s)

04-24-2025, 06:28 PM

jeepster09 replied to a thread April Foolishness in General Discussion

...

132 replies | 8576 view(s)

04-24-2025, 05:14 PM

dao replied to a thread Working Diagram in PM and CM Series Pistols

The source is a gif. When I right click on it and say Save Image As, it shows as a gif file.

6 replies | 534 view(s)

04-24-2025, 03:12 PM

187911 replied to a thread Is K9 Elite Still Being Produced? (K9098) in K Series Pistols

They all retail for a lot , a LOT more than 99.95% of people are willing to pay. It's just not sustainable. Most buy used. All of my K's and MK's...

17 replies | 8637 view(s)

04-24-2025, 01:37 PM

Slow Burn replied to a thread P380 failure to eject in P, S, and CW Series Pistols

The chamber cleaning brush arrived, I put it to work, and also gave everything else on the gun a pretty thorough cleaning and lubing, and that seems...

10 replies | 1580 view(s)