Tommy Gun Shop   Crimsontrace   Mitch Rosen   Tommy Gun
Page 8 of 8 FirstFirst ... 678
Results 71 to 80 of 80

Thread: CM9 Blown

  1. #71
    Join Date
    Feb 2013
    Posts
    169

    Default

    9mm headspaces on the forward rim of the case. If that was distorted in some way, whether it hit the ramp on the way in, or the front of the mag or slide stop, or if it just came out of the loading machine that way, it would not have taken much to prevent it from fully seating. A little less, the gun goes into battery and this thread does not exist. A little more and the gun refuses to fire. OR, since the gun has not been fired since, maybe a mechanical problem with the gun prevented it from going fully into battery. I think the slide lock lever pin has to be round, the channel under the barrel has to be clear and not buggered up, the breech face has to be smooth and not have something stuck on it or the extractor. Not having the gun in hand we can not determine that, but I am convinced the damage to the case is totally consistent with premature extraction. And you can NOT cure that with a little blue pill.

  2. #72
    Join Date
    Oct 2011
    Posts
    202

    Default

    FWIW I took a shot of the 9 next to the .40 for comparison.....the .40 does seat a little further into the chamber.


    "So Others May Live"


    PM9/night sights/CM9 barrel
    PM40/night sights

  3. #73
    Join Date
    Feb 2013
    Posts
    169

    Default

    You really need to shoot a little more of a right angle to see how much of a difference there is.

  4. #74
    Join Date
    Feb 2013
    Posts
    169

    Default

    Never mind, the second picture did not load right away.

    Yes, the .40 appears fully supported.

  5. #75
    Join Date
    Oct 2011
    Posts
    202

    Default

    After looking at the OP's blown casing again and the pics of the 9 and .40 barrels side by side with a round, I don't think the primer was struck prior to going into battery. The location of where the casing peeled back could have just as easily have happened to either of the barrels I have shown. The round in the .40 would have peeled forward but just not as far. My conclusion is that the casing was defective and the malfunction would have occurred regardless of how far the round was seated in the chamber of the barrel.

    That's my two cents and I'm sticking to it.


    "So Others May Live"


    PM9/night sights/CM9 barrel
    PM40/night sights

  6. #76
    Join Date
    Sep 2009
    Posts
    130

    Default

    my 21 cents. supported or non supported. THAT casing was gonna blow
    . My PM9 has over 40,000+ rounds through it, and runs much better than an illegal trying to get across our border


    NRA BENEFACTOR MEMBER


    MAY GOD BLESS MUGGSY

  7. #77
    Join Date
    Oct 2010
    Location
    Just this side of going around the bend
    Posts
    2,664

    Default

    Bet it felt something like this.
    Attached Images Attached Images
    On the internet, the number of posts do not correlate to actual knowledge.
    The notch is supposed to be there as well as the bulge at the front of the frame!
    You can't stop insane people from doing insane things by passing insane laws.






  8. #78
    Join Date
    Sep 2009
    Posts
    130

    Default

    damn, surv: I had a nice post after seeing that photo about Wild Bill and Monica, but I decided I best pass on posting it. I think I'm on thin ice anyhow and it is 70- degrees here, if u get my point.

    I am really trying to clean my act up but u damn guys just keep posting those dirty nasty ass photo's and I can't control myself..
    . My PM9 has over 40,000+ rounds through it, and runs much better than an illegal trying to get across our border


    NRA BENEFACTOR MEMBER


    MAY GOD BLESS MUGGSY

  9. #79
    Join Date
    Oct 2010
    Location
    Just this side of going around the bend
    Posts
    2,664

    Default

    Hey, at least I'm not posting porn pictures of goats and sheep!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    On the internet, the number of posts do not correlate to actual knowledge.
    The notch is supposed to be there as well as the bulge at the front of the frame!
    You can't stop insane people from doing insane things by passing insane laws.






  10. #80
    Join Date
    Dec 2015
    Location
    NOWHERE
    Posts
    25

    Default

    Well, I just read your post about blowing out the pistol. As it is now the end of 2015,could you please update us on the condition of the pistol, kahr's customer service, etc. Inquiring minds wanna know! Thanks

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Xssights   Kahr Shop   CrossBreed Holsters   Magnum Research new