Tommy Gun Shop   Kahr Shop   Mitch Rosen   Crimsontrace
Page 3 of 3 FirstFirst 123
Results 21 to 23 of 23

Thread: Recoil spring install

  1. #21
    Join Date
    Oct 2023
    Location
    Texas
    Posts
    4

    Default

    Working through old threads to learn what I can (recently bought a CW380 and a CM9). Had maybe a dozen failures to return to battery (by just a hair) on the second trip to the range for the .380, so thought new recoil springs might be worth a try, in case my preliminary break-in slide racking was too enthusiastic. Wish I'd seen this thread before putting on the new springs last night. I ended up using a Quick-Grip clamp, between the slide end and the spring guide flange (basically replacing my fingers) to compress the springs. I pushed an obstructing coil out of the way with the tip of a nail through the guide hole, and the guide came right on through. Then the flange can be slide from the pad of the clamp over onto the barrel lug. Just putting another idea out there. And many thanks to everyone for all the great ideas spread throughout these threads.

  2. #22
    Join Date
    Oct 2013
    Posts
    1,239

    Default update

    I want to share a possible solution.
    I've replaced recoil springs on P380s and CW380s a number of times over the years. New springs in this gun have always been a major pain the first time, but eventually I was always able to muscle them on using a table top or bookcase shelf. This week was the first time I've tried in a couple of years and I don't know if the new springs are even longer than they used to be or I've gotten weaker (probably) but I just couldn't. Compressing them overnight with a bolt, washer and nut didn't work for me either.
    It occurred to me to install ONLY the inner spring which seemed to be the main culprit. It wasn't easy but it was manageable. I then locked the slide back for awhile. When I took it apart and added the outer spring, it went together with only a short struggle. I don't know if I it would have worked had I not already tried to compress the springs, but I have new springs on order for my other copies of this pistol and this time I'll try installing just the inner spring first and report back. Wish I'd thought of it years ago.

    UPDATE - New springs arrived and I installed them. But first I did need to compress the inner springs for a short while. There was no way I could get an inner spring installed without doing that. They're sooo long out of the package - about 2x the length of the guide rod. After it had been compressed on a bolt for maybe a 1/2 hour, I was able to install an inner spring, lock the action open, wait 10-15 minutes, take it apart, add the outer spring and get it all together. I did that for 2 CW380s so that's how I plan to proceed with new springs from now on, unless someone comes up with a captive assembly for these pistols.
    Last edited by SlowBurn; 07-16-2024 at 10:58 AM. Reason: update
    Rest in peace Muggsy

    "Individual Muslims may show splendid qualities, but the influence of the religion paralyses the social development of those who follow it. No stronger retrograde force exists in the world." Winston Churchill 1899

  3. #23

    Default

    When I replaced the spring on my P9 I noticed the new one was somewhat longer but not doubled like that. I also counted the rings which the original has 19 turns and the replacement has 20. What I did was put a piece of 2x4 in my vise and drilled a hole large enough for a Phillips screwdriver to go through. Slid the spring onto the screwdriver and pushed it through the hole leaning by entire body weight on it to compress. Did it a few times and got it to the point it would work in the pistol.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Xssights   Tommy Gun   Magnum Research new   CrossBreed Holsters